Effect of geotextile ageing and geomembrane surface roughness on the geomembrane-geotextile interfaces for heap leaching applications

A series of large scale direct shear experiments is used to investigate the effect of the geomembrane (GMB) surface roughness, geotextile (GTX) properties, and GTX ageing, on the GMB-GTX interface shear behaviour. Interfaces involving smooth, coextruded textured, and structured surface GMBs underlying four different nonwoven needle-punched staple fibres (GTXs) with mass per unit areas between 200 and 2400 g/m², and a geocomposite drain (GCD) are examined at normal stresses between 250 and 1000 kPa. The results showed that the interlocking between the GMB and GTX increased with increasing the GMB asperity height and/or decreasing the mass per unit area of the GTX. For the interfaces that involved GTXs preaged prior to the shear box experiments for up to 2 years at 85 °C, it was found that the 2400 g/m² heat bonded two-layered GTX exhibited internal shear failure at low shear displacements. However, all the highly aged single layered GTXs showed an increase in the peak interface friction angles with the increase in their ageing. For these single layered GTX, the results suggest that assessing the interface friction angles using unaged GTXs for the stability analysis is conservative as long as the GTX remains intact in the field.     

木片筛余物高得率半化学法清洁制浆技术研究

以太阳纸业备料车间木片筛选碎料（筛余物）为原料，对其烧碱法半化学制浆的实验室工艺和生产试验进行了研究。结果表明，筛余物采用半化学法制浆可获得较高得率和环压强度的纸浆，且用碱量对纸浆性能有显著影响。相对8%NaOH （相对于绝干原料）化学预处理，采用14%NaOH化学预处理结合两段浆浓22%的高浓磨浆工艺，所制半化学浆抄造浆张的裂断长和环压指数分别达2.89 km和9.76 N·m/g，是前者的1.9倍和1.2倍，而且优于现用国内OCC废纸浆抄造浆张；生产试验得到的浆张性能指标与实验室相吻合，其中紧度和环压强度分别达到GB/T 13023—2008瓦楞芯（原）纸AA级和A级优等品要求。     

Advanced Friction–Wear Behavior of Organic Brake Pads Using a Newly Developed System

The objective of this study was to investigate the influence of an advanced performance system on the tribological behavior of brake pad material using a specially designed brake pad tester system following standard SAE J-661. The tribological behavior and friction and wear characteristics of the organic brake pad samples were evaluated. During braking tests, the samples, in contact with a cast iron disk, were studied at different disc speeds, temperatures, and braking cycles under a constant pressure. In order to understand the friction and wear behavior, the unworn surfaces, worn surfaces, and wear debris were characterized by means of scanning electron microscopy (SEM) and energy-dispersive X-ray (EDX). Furthermore, the surface characteristics and differences in the wear modes of the brake pad samples were examined. Wear debris was permitted to deform the brake pad surfaces, leading to friction layers and enabling the estimation of the friction behavior of the brake pads. The results showed that the best friction–wear behavior was obtained with lower braking cycles at low speeds and temperature. Thus, the newly developed brake pad tester system proved very effective in evaluating the performance of the brake pad samples.     

Moulded pulp products manufacturing with thermoforming

For an effective optimization of pulp thermoforming and of the moulded pulp products manufactured by this process, a full understanding of the process physics combined with full knowledge of the pressing equipment is necessary. For this reason, in this Addendum, we clarify how the process parameters “Holding time,” “Vacuum time,” “Cycle time,” and “Temperature” were interpreted and subsequently defined for the analysis of the process and product‐related outputs of the thermoforming experiments.     

Material removal efficiency improvement by orientation control of CMP pad surface asperities

This paper presents a novel method of improving material removal efficiency in the chemical mechanical polishing (CMP) process by optimizing the surface asperity orientation with respect to polishing motion. Feret's diameter plays a key role in increasing the number of working abrasives. Based on Feret's diameter model, an optimization method is proposed for the conditioning motion of a diamond dresser against a CMP pad. The radial velocity component of the dresser on the CMP pad is maximized by considering its direction of motion based on kinematic motion simulation. In addition, the pad cut rate profile is optimized to be uniform. Analytical and experimental investigations show that the ratio of radial and tangential velocity components is improved, yielding a larger Feret's diameter and 15% increase in the material removal rate.     

Morphology,adipocyte size,and fatty acid analysis of dairy cattle digital cushions,and the effect of body condition score and age

The digital cushion is an essential part of maintaining a healthy foot, working to dissipate foot strike and body weight forces and lameness from claw horn disruption lesions. Despite the importance of the digital cushion, little is known about the basic anatomy, adipocyte morphology, and fatty acid composition in relation to age, limb position, and body condition score. In total, 60 claws (from 17 cows) were selected and collected from a herd, ensuring that body condition score data and computed micro-tomography were known for each animal. Digital cushion tissue underwent histological staining combined with stereology, systematic random sampling, and cell morphology analysis, in addition to lipid extraction followed by fatty acid analysis. The results describe digital cushion architecture and adipocyte sizes. Adipocyte size was similar across all 4 claws (distal left lateral and medial and distal right lateral and medial) and across the ages (aged 2–7 yr); however, animals with body condition score of 3.00 or more at slaughter had a significantly increased cell size in comparison to those with a score of less than 2.50. Of 37 fatty acid methyl esters identified, 5 differed between either the body condition score or different age groups. C10:0 capric acid, C14:0 myristic acid, C15:0 pentadecanoic acid, and C20:0 arachidic acid percentages were all lesser in lower body condition score cows, whereas C22:1n-9 erucic acid measurements were lesser in younger cows. Saturated fatty acid, monounsaturated fatty acid, and polyunsaturated fatty acid percentages were not altered in the different claws, ages, or body condition score groups. Triglyceride quantities did not differ for claw position or age but had decreased quantities in lower body condition score animals. Digital cushion anatomy, cellular morphology, and fatty acid composition have been described in general and also in animals with differing ages, body condition scores, and in the differing claws. Understanding fat deposition, mobilization, and composition are essential in not only understanding the roles that the digital cushion plays but also in preventing disorders and maintaining cattle health and welfare.     

Corrosion inhibition of mild steel in 1 M HCl using Tamarindus indica extract: electrochemical,surface and spectroscopic studies

Abstract

We report, here, the corrosion inhibition of mild steel specimen in 1?M HCl by tamarind fruit pulp aqueous (TFPA) extract. The inhibition property in the presence of TFPA extract is studied using weight loss, polarization measurement and electrochemical impedance spectroscopy (EIS). The inhibitor efficiency is found to vary from 74% to 88% (weight loss method) with TFPA concentration of 100–600?ppm. The reduction in Tafel slopes shows that TFPA acts as a mixed-type inhibitor. The adsorption of the inhibitor on the metal surface follows Langmuir isotherm. The standard Gibbs free energy of adsorption value of –40?kJ/mol suggests the chemisorption of inhibitor molecules via coordinate bond. AFM results exhibit a decrease in the surface roughness of mild steel, exposed to 1?M HCl from 299?±?12 to 154?±?6.6?nm, with increasing concentration of inhibitor from 0 to 600?ppm due to the uniform coverage of inhibitor molecules on the metal surface. X-ray photoelectron spectroscopy de-convoluted high resolution profiles of C 1?s (carbon) for mild steel exposed to 1?M HCl with 600?ppm inhibitor show major peaks corresponding to sp³ C–C/C–H (284.9?eV) and oxygen bondings in C–OH, C=O, COOH with a binding energy of 285.9, 286.9, 288.5?eV, respectively, thereby confirming the adsorption of organic moieties on mild steel surface. Fourier transform infrared spectroscopy further confirms the adsorption of inhibitor molecules on the metal surface. Therefore, tamarind fruit pulp extract is a potential corrosion inhibitor for mild steel, which is cost-effective, green and non-toxic.     

Polishing pad for reducing edge roll-off while maintaining good global flatness of silicon wafer

In the double-sided polishing process of silicon wafers, there is a strong demand to reduce amount of edge roll-off (ERO) while improving global flatness of a wafer. In the present study, we clarified the negative effects of uneven wear of the polishing pads on the global flatness of a wafer can be suppressed when the deformation of the polishing pads is large. As for the ERO, we found small deformation of the polishing pad near the top surface was effective in reducing the amount of ERO. In addition, we revealed small distance from the surface of the polishing pad at the area under the wafer to that at the area around the wafer was also effective in reducing the amount of ERO. On the basis of the findings, we developed a three-layered polishing pad which was expected to reduce the amount of ERO while achieving the good global flatness.     

Natural-based polymers for antibacterial treatment of absorbent materials

In this study, polypropylene (PP) nonwoven fabric which can be used as topsheet layer of an absorbent hygienic product was modified by natural based antibacterial agents. Antibacterial herbal agents (cinnamaldehyde, geraniol, phenylethyl alcohol) were sprayed by ethanol or applied by means of polylactic acid (PLA) and polycyclohexene oxide (PCHO) based polymers prepared by three different chemical methods. Characterization of synthesized materials was conducted via thermogravimetric analysis (TGA), differential thermal analysis (DTA), and scanning electron microscopy–energy dispersive X–ray spectroscopy (SEM-EDX). Besides characterization, antibacterial and pH buffering performances of antibacterial polymers alone and on PP fabric were tested by antibacterial and pH tests. Effects of antibacterial treatments on air permeability and absorption period of nonwoven fabrics were also analyzed. According to the results, biopolymers changed the thermal stability of PP nonwoven fabric. Antibacterial performances can be ranked as cinnamaldehyde, geraniol, and phenylethyl alcohol from the best. Besides a slight decrease about liquid absorption performance, all of the treated topsheet fabrics are sufficient for an absorbent hygienic product. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48302.     

Shale gas pad development planning under price uncertainty

In this article, we study shale gas pad development under natural gas price uncertainty. We optimize the sequence of operations, gas curtailment, and storage on a single pad to maximize the net present value. The optimization problem is formulated as an mixed-integer linear programming model, which is similar to the one proposed by Ondeck et al. We investigate how natural gas price uncertainty affects the operation strategy in the pad development. Both two-stage and multistage stochastic programming are used as the mathematical framework to hedge against uncertainty. Our case study shows that there is value of using stochastic programming when the price variance is high. However, when the variance of the price is low, solving the stochastic programming problems does not create additional value compared with solving the deterministic problem.